How to remove and install the front wheel bearing and wheel hub assembly on Audi A4?

The driveaxle/hub bolt should first be loosened in order to remove the driveaxle and hub assembly. Next, loosen the wheel bolts and lift the vehicle using jackstands and make sure the vehicle is well supported on jackstands, followed by removing the wheel. The second step is to remove the brake caliper, caliper mounting bracket, and brake disc, making sure not to drop the brake caliper but to hold it with the use of wire or rope. Take off the shield by removing the shield mounting bolts and lose the upper control arms by removing them by unscrewing the steering knuckle. Gently insert the knuckle assembly and push the driveaxle out of the hub, it may be necessary to give the CV joint a stroke with a soft-faced hammer out of the hub or a puller may be needed, should the knuckle assembly not push free. Prop the driveaxle, do not overextend the inner CV joint. Lift off the mounting bolts of the hub/bearing assembly at the back of the steering knuckle and lift out the hub/bearing assembly. When it comes to bearing replacement, it is a job that needs professional skills and special tools that may not be available among some people and it is therefore good to trust a professional mechanic. Installation requires the mounting surfaces of the steering knuckle and the driveaxle splines to be smooth and without burrs and nicks and then the hub/bearing assembly should be attached to the steering knuckle and the bolts should be tightened to the recommended torque. Apply grease on the driveaxle splines and attach it to the hub/bearing assembly and install a new driveaxle/hub bolt without tightening it. Re-attach the upper control arms to the steering knuckle, re-fit clamp bolt and self-locking nut and tighten the nut pushing both control arms downward to avert misfitting of the balljoint studs. Install the caliper, caliper mounting bracket and brake disc, attach the fasteners to the recommended torque. Lastly, fit the wheel, dismount the jackstands, and drop the vehicle, then squeeze the driveaxle/hub bolt by positioning an assistant on the brakes, and then screw in the wheel bolts to the advised torque.

Genuine Audi A4 Wheel Hub

Wheel Axle Hub

Select Vehicle by Model
Select Vehicle by VIN

Select Vehicle by Model

Make

Model

Year

Select Vehicle by VIN

For the most accurate results, select vehicle by your VIN (Vehicle Identification Number).

10 Wheel Hubs found

View related parts
Audi A4 Hub & Bearing Assembly Part Number: 8W0-598-607
$191.02 MSRP: $267.53
You Save: $76.51 (29%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Wheel Hub
- Warranty: This genuine part is guaranteed by Audi's factory warranty.
Fits the following Vehicles:
- 2017-2018 Audi A4 | Premium, Premium Plus, Prestige | 4 Cyl 2.0 L GAS
View related parts
Audi A4 Rear Wheel Bearing Part Number: 8W0-407-625-J
$295.12 MSRP: $413.32
You Save: $118.20 (29%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Bearing
- Replaces: 8W0-407-625-B
- Warranty: This genuine part is guaranteed by Audi's factory warranty.
Fits the following Vehicles:
- 2018-2020 Audi A4 | Premium, Premium Plus, Prestige, Titanium | 4 Cyl 2.0 L GAS
View related parts
Audi A4 Front Hub Part Number: 4A0-407-615-G
$282.61 MSRP: $395.82
You Save: $113.21 (29%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Wheel Hub; Front Hub
- Replaces: 4B0-407-613-B, 4A0-407-615-D, 4B0-407-613, 4A0-407-615-F, 4B0-407-613-A
- Warranty: This genuine part is guaranteed by Audi's factory warranty.
Fits the following Vehicles:
- 1996-2009 Audi A4 | Avant, Base, Cabriolet | 4 Cyl 1.8 L GAS, 4 Cyl 2.0 L GAS, 6 Cyl 2.8 L GAS, 6 Cyl 3.0 L GAS, 6 Cyl 3.2 L GAS
View related parts
Audi A4 Front Hub & Bearing Part Number: 8K0-407-607
$280.84 MSRP: $393.33
You Save: $112.49 (29%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Wheel Hub; Front Hub & Bearing, Hub & Bearing
- Warranty: This genuine part is guaranteed by Audi's factory warranty.
Fits the following Vehicles:
- 2009-2016 Audi A4 | Base, Premium, Premium Plus, Prestige | 4 Cyl 2.0 L GAS
View related parts
Audi A4 Front Wheel Bearing Part Number: 8K0-407-613-B
$328.44 MSRP: $460.01
You Save: $131.57 (29%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Wheel Hub; Front Hub, Front Wheel Bearing, Rear Hub
- Warranty: This genuine part is guaranteed by Audi's factory warranty.
Fits the following Vehicles:
- 2009-2016 Audi A4 | Base, Premium, Premium Plus, Prestige | 4 Cyl 2.0 L GAS
View related parts
Audi A4 Front Hub Part Number: 8D0-407-615-E
$313.99 MSRP: $439.76
You Save: $125.77 (29%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Wheel Hub; Hub
- Position: Front
- Warranty: This genuine part is guaranteed by Audi's factory warranty.
Fits the following Vehicles:
- 1997-2001 Audi A4 | Base | 4 Cyl 1.8 L GAS
View related parts
Audi A4 Rear Hub Part Number: 8W0-501-652-D
$393.89 MSRP: $551.66
You Save: $157.77 (29%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Wheel Hub; Hub, Rear Hub
- Replaces: 8W0-501-652-A
- Warranty: This genuine part is guaranteed by Audi's factory warranty.
Fits the following Vehicles:
- 2018-2020 Audi A4 | Premium, Premium Plus, Prestige, Titanium | 4 Cyl 2.0 L GAS
View related parts
Audi A4 Rear Hub & Bearing Part Number: 8W0-501-611-B
$421.26 MSRP: $590.01
You Save: $168.75 (29%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Wheel Hub; Rear Hub Bearings
- Warranty: This genuine part is guaranteed by Audi's factory warranty.
Fits the following Vehicles:
- 2017-2020 Audi A4 | Premium, Premium Plus, Prestige, Titanium | 4 Cyl 2.0 L GAS
View related parts
Audi A4 Front Hub Part Number: 8W0-407-613
$476.00 MSRP: $666.66
You Save: $190.66 (29%)
Ships in 1-2 Business Days
ADD TO CART
Product Specifications
- Other Name: Wheel Hub; Front Hub, Rear Hub
- Warranty: This genuine part is guaranteed by Audi's factory warranty.
Fits the following Vehicles:
- 2017-2020 Audi A4 | Premium, Premium Plus, Prestige, Titanium | 4 Cyl 2.0 L GAS
View related parts
Audi A4 Front Hub Part Number: 357-407-613-B
Product Specifications
- Other Name: Wheel Hub; Front Hub, Hub
- Replaces: 357-407-615, 357-407-615-E
- Warranty: This genuine part is guaranteed by Audi's factory warranty.
Fits the following Vehicles:
- 2007-2009, 1996-2001 Audi A4 | Avant, Base, Cabriolet | 4 Cyl 1.8 L GAS, 4 Cyl 2.0 L GAS, 6 Cyl 2.8 L GAS, 6 Cyl 3.2 L GAS

Audi A4 Wheel Hub

The Audi A4 Wheel Hub attaches the wheel to the suspension but allows the wheel to rotate without difficulty, and this makes the steering and braking stable. The Wheel Hub firmly screws the wheel, bearings and usually the ABS sensor together, so there is no movement of power and data across the assembly. The Wheel Hub and bearing assembly is pre-packed in most modern Audi sedans and attaches as a single unit with bolts, thus simplifying the installation process and preventing contamination. Older models and the rear positions still use press-in hub bearings which require the removal of the steering knuckle, and non-driven axles may have rebuildable hub bearings with opposed tapers, providing long-serving Audi owners with the option to do repairs cheaply. Regardless of the differences, each Wheel Hub is made of hardened steel and studs, and has exact torque requirements to ensure that the rim is safe and maintains the sharp, reactive feel that drivers desire from an Audi. Owners need to have an identical match of bolt pattern, flange offset and axle length to factory values when buying a replacement to ensure that their A4 retains the same self-confident road behavior designed by Audi. The hub assembly prevents the entry of water and grit, reduces vibration, and keeps the bearings on target, which also ensures proper ABS readout, all of which lead to smoother rides and increased tire life.

Choose original equipment manufacturer Wheel Hub for great performance and strong durability. They use Audi's official craftsmanship and high-grade materials, and meet strict quality standards. Are you looking for quality Wheel Hub at a good price? Come to our online store. We carry a wide range of genuine parts for your Audi A4 and the prices are competitive. Each part comes with the manufacturer's warranty. You can install with confidence and get steady results. Over time, you'll save money and avoid hassle. Keep your maintenance simple and protect your vehicle with OEM parts. Get the quality your A4 needs now.

Audi A4 Wheel Hub Parts and Q&A

Front Hub
4A0-407-615-G
Q: How to remove and install the front wheel bearing and wheel hub assembly on Audi A4?
A:
The driveaxle/hub bolt should first be loosened in order to remove the driveaxle and hub assembly. Next, loosen the wheel bolts and lift the vehicle using jackstands and make sure the vehicle is well supported on jackstands, followed by removing the wheel. The second step is to remove the brake caliper, caliper mounting bracket, and brake disc, making sure not to drop the brake caliper but to hold it with the use of wire or rope. Take off the shield by removing the shield mounting bolts and lose the upper Control Arms by removing them by unscrewing the Steering Knuckle. Gently insert the knuckle assembly and push the driveaxle out of the hub, it may be necessary to give the CV joint a stroke with a soft-faced hammer out of the hub or a puller may be needed, should the knuckle assembly not push free. Prop the driveaxle, do not overextend the inner CV joint. Lift off the mounting bolts of the hub/bearing assembly at the back of the steering knuckle and lift out the hub/bearing assembly. When it comes to bearing replacement, it is a job that needs professional skills and special tools that may not be available among some people and it is therefore good to trust a professional mechanic. Installation requires the mounting surfaces of the steering knuckle and the driveaxle splines to be smooth and without burrs and nicks and then the hub/bearing assembly should be attached to the steering knuckle and the bolts should be tightened to the recommended torque. Apply grease on the driveaxle splines and attach it to the hub/bearing assembly and install a new driveaxle/hub bolt without tightening it. Re-attach the upper control arms to the steering knuckle, re-fit clamp bolt and self-locking nut and tighten the nut pushing both control arms downward to avert misfitting of the balljoint studs. Install the caliper, caliper mounting bracket and brake disc, attach the fasteners to the recommended torque. Lastly, fit the wheel, dismount the jackstands, and drop the vehicle, then squeeze the driveaxle/hub bolt by positioning an assistant on the brakes, and then screw in the wheel bolts to the advised torque.